CCNA2 Final Exam (v5.03) 2016

CCNA2 Final Exam Answer 2015 v5.03 2016 Refer to the exhibit. A network administrator is configuring a router as a DHCPv6 server. The administrator issues a show ipv6 dhcp pool command to verify the configuration. Which statement explains the reason that the number of active clients is 0? The default gateway address is not provided […]
Continue reading…

 

CCNA2 Practice Final Exam (v5.03) 2016

CCNA2 Practice Final Exam Answer v5.03 2016 A client is using SLAAC to obtain an IPv6 address for its interface. After an address has been generated and applied to the interface, what must the client do before it can begin to use this IPv6 address? It must send a DHCPv6 INFORMATION-REQUEST message to request the […]
Continue reading…

 

CCNA2 Chapter 11 Exam (v5.03) 2016

CCNA2 Chapter 11 Exam Answer v5.03 2016 Typically, which network device would be used to perform NAT for a corporate environment? DHCP server host device router server switch Which type of NAT maps a single inside local address to a single inside global address? dynamic static port address translation overloading Several key servers in an […]
Continue reading…

 

CCNA2 Chapter 10 Exam (v5.03) 2016

CCNA2 Chapter 10 Exam Answer v5.03 2016 Refer to the exhibit. A network administrator is implementing the stateless DHCPv6 operation for the company. Clients are configuring IPv6 addresses as expected. However, the clients are not getting the DNS server address and the domain name information configured in the DHCP pool. What could be the cause […]
Continue reading…

 

CCNA2 Chapter 9 Exam (v5.03) 2016

CCNA2 Chapter 9 Exam Answer v5.03 2016 Which three statements describe ACL processing of packets? (Choose three.) An implicit deny any rejects any packet that does not match any ACE. A packet can either be rejected or forwarded as directed by the ACE that is matched. A packet that has been denied by one ACE […]
Continue reading…

 

CCNA2 Chapter 8 Exam (v5.03) 2016

CCNA2 Chapter 8 Exam  Answer v5.03 2016 A router is participating in an OSPFv2 domain. What will always happen if the dead interval expires before the router receives a hello packet from an adjacent DROTHER OSPF router? OSPF will run a new DR/BDR election. SPF will run and determine which neighbor router is “down”. A […]
Continue reading…

 

CCNA2 Chapter 7 Exam (v5.03) 2016

CCNA2 Chapter 7 Exam Answer v5.03 2016 What two tasks do dynamic routing protocols perform? (Choose two.) discover hosts update and maintain routing tables propagate host default gateways network discovery assign IP addressing What is a disadvantage of using dynamic routing protocols? They are only suitable for simple topologies. Their configuration complexity increases as the […]
Continue reading…

 

CCNA2 Chapter 6 Exam (v5.03) 2016

CCNA2 Chapter 6 Exam Answer 2016 v5.03 Refer to the exhibit. What command would be used to configure a static route on R1 so that traffic from both LANs can reach the 2001:db8:1:4::/64 remote network? ipv6 route ::/0 serial0/0/0 ipv6 route 2001:db8:1:4::/64 2001:db8:1:3::1 ipv6 route 2001:db8:1:4::/64 2001:db8:1:3::2 ipv6 route 2001:db8:1::/65 2001:db8:1:3::1 Refer to the exhibit. […]
Continue reading…

 

CCNA2 Chapter 5 Exam (v5.03) 2016

CCNA2 Chapter 5 Exam Answer 2016 v5.03 What is a disadvantage of using router-on-a-stick inter-VLAN routing? does not support VLAN-tagged packets requires the use of more physical interfaces than legacy inter-VLAN routing does not scale well beyond 50 VLANs requires the use of multiple router interfaces configured to operate as access links How is traffic […]
Continue reading…

 

CCNA2 Chapter 4 Exam (v5.03) 2016

CCNA2 Chapter 4 Exam Answer 2016 v5.03 What are two functions of a router? (Choose two.) It connects multiple IP networks. It controls the flow of data via the use of Layer 2 addresses. It determines the best path to send packets. It manages the VLAN database. It increases the size of the broadcast domain. […]
Continue reading…

 

CCNA2 Chapter 3 Exam (v5.03) 2016

CCNA2 Chapter 3 Exam Answer 2016 v5.03 Which three statements accurately describe VLAN types? (Choose three). A management VLAN is any VLAN that is configured to access management features of the switch. A data VLAN is used to carry VLAN management data and user-generated traffic. After the initial boot of an unconfigured switch, all ports […]
Continue reading…

 

CCNA2 Pretest Exam (v5.03) 2016

CCNA2 Pretest Exam Answer v5.03 2016 Which two components are configured via software in order for a PC to participate in a network environment? (Choose two.)  MAC address IP address kernel shell subnet mask What is the correct order for PDU encapsulation? To revert to a previous configuration, an administrator issues the command copy tftp […]
Continue reading…

 

CCNA2 Chapter 2 Exam (v5.03) 2016

CCNA2 Chapter 2 Exam Answer 2016 v5.03 Which interface is the default location that would contain the IP address used to manage a 24-port Ethernet switch? VLAN 1 Fa0/0 Fa0/1 interface connected to the default gateway VLAN 99 A production switch is reloaded and finishes with a Switch> prompt. What two facts can be determined? […]
Continue reading…

 

CCNA2 Chapter 1 Exam (v5.03) 2018

CCNA2 Chapter 1 Exam Answer 2018 v5.03 What is a basic function of the Cisco Borderless Architecture distribution layer? acting as a backbone aggregating all the campus blocks aggregating Layer 3 routing boundaries providing access to end user devices A network designer must provide a rationale to a customer for a design which will move […]
Continue reading…